![]() ![]() Which makes me wonder, If one end of one of these cables is plugged into an active device (i.e. Choose from our selection of hose strain relief, including cable support grips, plastic submersible cord grips, and more. Which makes me wonder, If one end of one of these cables is plugged into an active device (i.e., turned on), and the exposed pins on the free end of the cable are shorted or gets wet, can this cause the electronics in the plug to be damaged? Is there anyone in the forum here familiar with the guts of the lightning cable plugs that might answer this? Move grease-dispensing guns in any direction without kinking the outlet hose. There are electronics inside the plug between the wires and the pin connectors. I.e., they don't just connect the wires to the various pins on the connector. If I understand correctly those lightning plugs aren't passive. I've had several 3rd party cables just stop working (6 in the last 3 years). You'll notice that the cable on your other connector is a little heavier and stiffer which will protect it a little more from too much flexing near the plug.Īlso, even if the cable doesn't break, there are some other things unique to these cables that can go wrong. Cables breaking at the plug is a common problem across the industry. This is actually very nice except they won't take much abuse. Top and Side entry optionsĢ89-007Low profile solid shell EMI backshell, Elliptical entry, panel mount.Apple uses a lightweight and flexible wire for connecting their mobile products. Top and Side entry optionsĢ89-008Low profile solid shell EMI backshell, Elliptical entry. Lightweight, Low-Profile Backshells for Glenair Signature Series 28 Hiper-D High-Performance M24308 Intermateable ConnectorsĢ89-005Low profile split shell EMI backshell, Elliptical entry. For panel mount and cable-to-cable connectors. For panel mount and cable-to-cable connectors.ĥ57-186Lightweight composite thermoplastic construction with banding porch platform for shield termination with Band-Master ATS ® bands. Split Shell EMI/RFI Backshells with Variable-Length Shroud for Connector Protectionĥ50-039Aluminum construction with banding porch platform for shield termination with Band-Master ATS ® bands. Configurable with 1, 2, or 3 cable entries. Lightweight aluminum.ĮMI/RFI Split-Shell Standard Flange Banding Backshell with Removable Banding Porchesĥ57-609Split construction with separable banding platforms (allows inspection of wire-toconnector termination without disrupting cable shield termination). Lightweight aluminum with lanyard attachment options.ĥ57T316Shorting can backshell for protection of stand-alone connectors. Top, Side, or End entry options.ĥ57-467Saddle bar clamp with silicone pads for easy installation of flat cable bundleĥ57-493Shorting can backshell for protection of stand-alone connectors. Dual, Top, Round cable entry.ĥ57-387Cone-and-ring shield termination (nonbanding). Round or Elliptical, Top, Side, End, and 45° cable entry options.ĥ57-080Banding porch platform for shield termination with Band-Master ATS ® bands. Termination with Band-Master ATS ® bands. Solid Shell Standard Flange Lightweight Aluminum EMI/RFI Backshells Short side, Round cable entry.ĥ57-281Banding porch platform for shield termination with Band-Master ATS ® Micro bands. Long side, round cable entry.ĥ57-109Banding porch platform for shield termination with Band-Master ATS ® Standard or Micro bands. Ranger® Liquid Tight Strain Relief Connector, Aluminum, Straight, Portable Cord, 0.310 to 0.560 in., 1/2 in. Side and 45° entry options.ĥ57-108Banding porch platform for shield termination with Band-Master ATS ® Standard or Micro bands. Top, Round cable entry.ĥ57-319Banding porch platform for shield termination with Band-Master ATS ® Standard or Micro bands. Note: These accessories do not accommodate connectors with flange tabsĥ57-107Banding porch platform for shield termination with Band-Master ATS ® bands. Solid Shell Low-Profile Flange Lightweight Aluminum, Trapezoidal EMI/RFI Backshells Glenair Improved Designs for Removable-Entry and Cable Clamp Rectangular Backshells.ESA/ESCC-to-Glenair Part Number Cross-Reference.Lightweight, Low-Profile Backshells for Glenair Signature Series 28 Hiper-D High-Performance M24308 Intermateable Connectors.Split Shell EMI/RFI Backshells with Variable-Length Shroud for Connector Protection.EMI/RFI Split-Shell Standard Flange Banding Backshell with Removable Banding Porches.Solid Shell Standard Flange Lightweight Aluminum EMI/RFI Backshells.Solid Shell Low-Profile Flange Lightweight Aluminum, Trapezoidal EMI/RFI Backshells.Space-Grade Backshells and Shielding Accessories > D-Subminiature These backshells are compatible with industry-standard metal shell M24308 type connectors. Electroless nickel is the most widely used finish. ![]() These backshells are made out of aluminum alloy or composite thermoplastic. D-Sub EMI backshells are used to ground cable shields for electromagnetic compatibility, and to provide strain relief and mechanical protection of wire-to-connector terminations. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |